公司新聞
冷再生機時打滑的原因及方法
來源：http://lzqdw.com/ 日期：2023-05-08
客戶在冷再生機使用過程中，不可避免地會出現消耗和磨損，其中，冷再生機輸送帶特別容易出現問題，運行時間長，可能出現打滑現象，影響工作效率。下面冷再生機租賃廠家來分析下打滑的原因和解決辦法。
Customers inevitably experience consumption and wear during the use of the cold regeneration machine. Among them, the conveyor belt of the cold regeneration machine is particularly prone to problems, running for a long time, and may slip, affecting work efficiency. Let's analyze the reasons and solutions for the slipping of the cold regeneration machine rental manufacturer below.
1、初始張力太小。
1. The initial tension is too low.
輸送帶離開滾筒的張力不夠，會引起皮帶打滑。一般來說，這種情況是在啟動時發生的。如果你想解決它，你必須調整張力裝置和增加初始張力。
Insufficient tension of the conveyor belt leaving the drum can cause the belt to slip. Generally speaking, this situation occurs during startup. If you want to solve it, you must adjust the tension device and increase the initial tension.
2、摩擦力是不夠的。
2. Friction is not enough.
傳動滾筒與輸送帶之間的摩擦力不足以引起滑動。造成這種現象的主要原因是輸送帶上的水或環境潮濕。解決方法：在氣缸中加入一些松香末。注意不要用手而應用鼓風設備吹入，以免發生事故。
The friction between the transmission drum and the conveyor belt is not sufficient to cause sliding. The main reason for this phenomenon is the water on the conveyor belt or the humid environment. Solution: Add some rosin powder to the cylinder. Be careful not to use your hands and blow in with an air blowing device to avoid accidents.
3、軸承損壞
3. Bearing damage
尾部滾子軸承損壞或不旋轉。造成損壞的原因是機器尾部太浮、太沉，不能及時修理和更換損壞的或不靈活的部件，這導致由打滑引起的阻力增加。
The tail roller bearing is damaged or does not rotate. The reason for the damage is that the tail of the machine is too floating and heavy, and damaged or inflexible components cannot be repaired and replaced in a timely manner, resulting in increased resistance caused by slipping.
4、起步太快。
4. Starting too fast.
起動速度太快，不能打滑。這個時候可慢速啟動。如果使用鼠籠電機，則可以移動兩次，然后被激活，還可以有效地克服打滑現象。
The starting speed is too fast to slip. At this time, it can be started slowly. If a squirrel cage motor is used, it can be moved twice and then activated, effectively overcoming slipping.
5、輸送帶負荷過大。
5. The conveyor belt is overloaded.
輸送帶的負荷過大，超過電機能力也會打滑。打滑的優點是保護電機。否則，電動機將長期燃燒。但對于運行來說則是打滑事故。
The load of the conveyor belt is too large, and exceeding the motor capacity can also cause slipping. The advantage of slipping is to protect the motor. Otherwise, the motor will burn for a long time. But for operation, it is a slip accident.
以上是冷再生機時打滑的原因及方法相關信息的所有內容了，想要了解更多關于冷再生機相關內容，請繼續關注瀏覽我們網站http://lzqdw.com。
The above is all the information about the reasons and methods of slipping during the cold regeneration machine. If you want to learn more about the cold regeneration machine, please continue to follow and browse our website http://lzqdw.com 。
公司地址：濟南市槐蔭區經一路273號群盛華城2號樓1-404
公司名稱：山東途暢路橋工程有限公司 
備案號：