行業資訊
冷再生機減速機齒輪油的更換方式
來源：http://lzqdw.com/ 日期：2023-04-03
準備事項：
Preparation:
1、場地:要求無塵硬化路面，面積應在200平方米左右，盡量是庫房，但要有足夠25噸的吊車的工作高度和半徑。
1. Site: Dust free and hardened pavement is required, with an area of about 200 square meters. It should be a warehouse as much as possible, but it should have a working height and radius sufficient for a 25 ton crane.
2、設施：25噸吊車一臺（20噸也可以）。
2. Facilities: One 25 ton crane (20 tons is also acceptable).
3、配件：進口美孚齒輪油9升、衛生紙10卷、塑料帶20個、廢油桶2個、緊固膠262/340一支、密封膠587一支、黃油一袋，細線繩20米、12*45的帶母螺栓30套、4*30開口銷10個。
3. Accessories: 9 liters of imported Mobil gear oil, 10 rolls of toilet paper, 20 plastic belts, 2 waste oil drums, a piece of fastening glue 262/340, a piece of sealant 587, a bag of butter, 20 meters of string, 30 sets of 12 * 45 bolts with nuts, and 10 4 * 30 cotter pins.
4、工具：10、16、18、19、21、22、24、30套筒和扳手至少一套、快速扳手及長、短接桿各一、加力桿一根、30的輪胎扳手、10毫米的內六角扳手、55的活口扳手兩把、小號活口扳手一把、小號的老虎鉗一把、手鉗一把、一字螺絲刀一把、大小錘頭各一、撬棍兩根，配備氣動扳手和氣泵，能提高工作效率。
4. Tools: At least one set of 10, 16, 18, 19, 21, 22, 24, 30 sockets and wrenches, one quick wrench and one long and short extension rod each, one force bar, 30 tire wrench, 10 mm hexagonal wrench, two 55 adjustable wrenches, one small adjustable wrench, one small vise, one hand wrench, one slotted screwdriver, one large and small hammer head each, two crowbars, equipped with pneumatic wrench and air pump, can improve work efficiency.
（冷再生機租賃減速機油位及減速機油的檢查：先切斷電源，等待減速機冷卻后打開放油螺塞，檢查油是否充滿，避免漏油，取油樣，檢查油色澤及粘度指數，如果油明顯渾濁，建議盡快更換。新減速機使用后（500-1000）小時更換新油（將內部污油沖干凈），其后每使用1500小時需要更換油一次，但是在使用過程中，仍需要檢查油的質量，若油有老化、變質情況要隨時更換。）
(Inspection of the oil level and speed reducer oil for leasing a cold regeneration machine: First cut off the power supply, wait for the speed reducer to cool down, open the oil drain plug, check whether the oil is full to avoid oil leakage, take an oil sample, check the oil color and viscosity index, and if the oil is obviously turbid, it is recommended to replace it as soon as possible. After using a new speed reducer, replace it with a new oil (flush the internal dirty oil) within (500-1000) hours, and then replace the oil every 1500 hours of use, "However, during use, it is still necessary to check the quality of the oil and replace it at any time if there is aging or deterioration."
此外冷再生機在施工過程中會有大量的灰塵落到再生機的表面，包括施工中沾污的油跡等污染物，影響外觀事小，更為嚴重的是成為腐蝕的誘發因素。冷再生機在施工過程中會有大量的灰塵落到再生機的表面，包括施工中沾污的油跡等污染物，影響外觀事小，更為嚴重的是成為腐蝕的誘發因素。更多事項就來我們網站http://lzqdw.com咨詢吧！
In addition, during the construction process of the cold regenerator, a large amount of dust will fall onto the surface of the regenerator, including pollutants such as oil stains that are contaminated during construction, which have a small impact on the appearance, and more importantly, become an inducing factor for corrosion. During the construction process of a cold regenerator, a large amount of dust will fall onto the surface of the regenerator, including pollutants such as oil stains that are contaminated during construction, which have a small impact on the appearance and, more seriously, become an inducing factor for corrosion. For more information, please visit our website http://lzqdw.com Consult!
公司地址：濟南市槐蔭區經一路273號群盛華城2號樓1-404
公司名稱：山東途暢路橋工程有限公司 
備案號：