冷再生機的操作規程

Operating procedures for cold regeneration machines

　　一、準備工作

1、 Preparation work

　　1.檢查冷再生機的外觀，確認設備是否完好，并檢查相關配件。

1. Check the appearance of the cold regeneration system, confirm if the equipment is in good condition, and inspect the relevant accessories.

　　2.檢查設備的工作區域和周邊環境，保證安全和通風條件。

2. Check the working area and surrounding environment of the equipment to ensure safety and ventilation conditions.

　　3.檢查冷再生機的電氣系統是否正常，電源接口是否穩定可靠。

3. Check whether the electrical system of the cold regeneration is normal and whether the power interface is stable and reliable.

　　4.檢查冷再生機的水路系統，調整水量和水壓。

4. Check the water system for cold regeneration, adjust the water volume and pressure.

　　二、操作步驟

2、 Operation steps

　　1.開機操作

1. Power on operation

　　（1）按下開機按鈕，啟動冷再生機。

(1) Press the power button to start the cold regeneration machine.

　　（2）打開水泵，使水流經過冷再生機，循環流動。

(2) Turn on the water pump and allow the water flow to circulate through the cold regeneration machine.

　?。?）設定冷再生機的計時器和溫度控制器，并驗證其功能。

(3) Set the timer and temperature controller of the cold regeneration machine and verify their functionality.

　　2.冷卻操作

2. Cooling operation

　?。?）將需要冷卻的物品放入冷藏室中，注意不要堆積過高。

(1) Put the items that need to be cooled into the refrigeration room, being careful not to pile them up too high.

　　（2）調整溫度，使設備開始工作，直到達到預設的溫度。

(2) Adjust the temperature to start the device working until it reaches the preset temperature.

　　3.停機操作

3. Shutdown operation

　　（1）按下停機按鈕，停止冷再生機的工作。

(1) Press the shutdown button to stop the operation of the cold regeneration machine.

　　（2）關閉水泵，中止水的循環流動。

(2) Turn off the water pump and stop the circulation of water in the middle.

　　（3）將冷藏室中的物品清理干凈，關上門。

(3) Clean up the items in the refrigeration room and close the door.

　　三、注意事項

3、 Precautions

　　1.操作前必須檢查設備正常，防止出現故障。

1. Before operation, it is necessary to check that the equipment is functioning properly to prevent malfunctions.

　　2.使用前應保證工作區域清潔干凈，避免進入雜質和異物。

2. Before use, ensure that the work area is clean and avoid entering impurities and foreign objects.

　　3.操作時必須戴上手套和安全帽等個人防護裝備。

3. Personal protective equipment such as gloves and safety helmets must be worn during operation.

　　4.操作期間不得隨意觸摸設備和工作區域。

4. During operation, do not touch the equipment and work area without permission.

　　5.設備必須經常保養和清潔，以延長使用壽命。

5. The equipment must be regularly maintained and cleaned to extend its service life.

　　6.操作結束后，及時關閉設備和清理工作區域。

6. After the operation is completed, promptly shut down the equipment and clean the work area.

本文來自：冷再生機租賃 更多的內容請點擊：http://lzqdw.com 我們將會為您提問的問題提供一個滿意的服務，歡迎您的來電！

This article is from: Cold Recycling Machine Rental. For more information, please click on: http://lzqdw.com We will provide satisfactory service for the questions you ask. Welcome to call us!